Matek ELRS PWM Receiver ELRS-R24-P6 (2.4ghz)

$15.00 USD

left in stock

Out of stock
Order in H, M, Seconds (before 1pm AEST) for same day despatch
Add to Wishlist
SKU: 24326N/A W/H: W-02-C-04 N/A Barcode: N/A Shipping Weight: 9g N/A Categories: Drone RC RX Receivers , ELRS Express LRS Receivers & Modules , FPV Antennas , Matek , Radio Gear , Tags: 2.4ghz, ELRS, Matek, Receiver

We accept the following payment methods
       

Are you looking to buy a Matek ELRS 2.4GHz R24-P6 Receiver in Australia?

ELRS has quickly become one of the most popular link system choices for many pilots, and we are excited to bring Matek's lineup of these receivers to you.

SPECIFICATIONS:

  • ESP8285, SX1281
  • Antenna connector: IPEX MHF 1
  • 6x PWM outputs
  • Support 2~8S VBat voltage sense
  • RF Frequency: 2.4GHz (2400~2480MHz)
  • Telemetry power: 12dbm
  • Receiver output protocol: PWM
  • Input voltage: 4~9V DC @ “+” pad
  • Voltage sense: 34V Max. @ “VBat” pad
  • Power dissipation:  45mA(binding), 85mA(wifi mode)
  • PCB size: 20mm x 18mm
  • Weight: 2g w/ antenna

PACKAGE INCLUDES:

  • 1x MATEK ELRS-R24-P6 ELRS 2.4GHZ PWM RECEIVER
  • 1x IPEX MHF1 Antennas. 15cm
  • Dupont 2.54 pins  (Board is shipped unsoldered)

FIRMWARE:

  • ExpressLRS 3.0 or newer,   DIY 2.4 GHz / DIY 2400 RX PWMP EX
  • ExpressLRS wiki for PWM receiver, Click HERE
  • Make sure Receiver and TX module both are running ExpressLRS 3.0 or newer

FLASHING INFORMATION:

  • Receiver has ExpressLRS 3.0 preloaded with binding phrase “123456”,  the Receiver will never enter binding mode if using the traditional binding procedure.
  • You need to reflash it with your binding phrase OR go into WebUI to set your binding phrase.

Flashing via Wifi

  • Disconnect ESC and servos from receiver first.
  • Power on receiver by 5V source. Receiver’s LED(Red) will blink slow at first, and after 20s, it should blink fast indicating it’s on Wifi Hotspot Mode.
  • More detailed steps,  pls refer this page.
  • Target: DIY 2.4 GHz / DIY 2400 RX PWMP EX

Flashing via UART

  1. Disconnect ESC and servos from receiver first.
  2. Wire the receiver into the USB-TTL adapter, with TX on receiver connected to the Rx on the USB-TTL, and RX on receiver connected to the Tx of the USB-TTL. Wire 5V and GND of the USB-TTL to 5V and GND of the Receiver.
  3. Press the boot button while powering on the receiver, then release – the Red LED on receiver should now be solid.
  4. Select the target DIY 2.4 GHz / DIY 2400 RX PWMP EX  and  “UART” for Flashing Method,  set your bind phrase and Firmware Options and once done, click on Build and Flash.

Browse more

Sunday,Monday,Tuesday,Wednesday,Thursday,Friday,Saturday
January,February,March,April,May,June,July,August,September,October,November,December
Not enough items available. Only [max] left.
Shopping cart

Your cart is empty.

Return To Shop

Add Order Note Edit Order Note
Estimate Shipping
Add A Coupon

Estimate Shipping

Add A Coupon

Coupon code will work on checkout page

Matek ELRS PWM Receiver ELRS-R24-P6 (2.4ghz)

$15.00